FMEA Process Analysis Step by Step

FMEA Insights in Manufacturing Industry

Estimated Reading Time: 5 minutes

The main agenda of FMEA is to reduce the effects and failures during the design and production process in manufacturing industries.
By Jyothsna Sai Swaroop Surisetty, Associate Consultant in R&D and Career Coaching, Cademix Institute of Technology

Introduction of Failure Mode and Effects Analysis (FMEA)

Over the decades, FMEAs have been used as a method to detect and minimize risk. Firstly, in the 1940s, the US military used the commonly recognized FMEAs. They developed the technique to minimize variance sources and subsequent possible failures in munitions production – and proved a highly successful method. After that automotive industry started to adapt to FMEA in the 1970s.

There are many examples of products that are poorly designed or processed, that we will review in the following. In fact, these product failures are discussed in the public where manufacturers, service providers, and suppliers are shown to be incapable of providing a safe product. However, to overcome these problems FMEA is one of the precise tools that is used to reduce failures. We will discuss the pros and how it works in large, medium, and small scale industries.

The word “Failure modes” means how something could go wrong or how it might go wrong. That means it includes errors or defects that may be potential or actual, particularly those affecting the customer.
The word “Effects analysis” refers to the study of the impacts of these deficiencies.

FMEA is not a substitute for good engineering but it improves good engineering by applying the knowledge and experience of certain Teams. It is to check the progress of the design of a product or process by measuring its risk of failure.

Types of FMEA

FMEA is divided into two categories:

Design FMEA: It examines the possibilities for product malfunctions, reduced product lifecycle, and safety regulations. Below are a few things that should take into consideration before designing a product

  • Material properties
  • Tolerances
  • Interfaces with other parts
  • Geometry

Process FMEA: It Identifies failures affecting product quality, reduced process reliability, customer complaints, and safety or potential pollution that can be obtained from materials. Here are some important factors while such as

  • Human concerns
  • Methods adopted during handling
  • Materials used

Advantages

Firstly, It improves a manufacturing firm’s efficiency by exploring the FMEA process Secondly, it reduces the development time and cost during the production process. Also, FMEA reduces the time required to take into account possible conflicts with the design concept and prevents the breakage of vital elements of the project. Likewise, it helps define characteristics of critical quality.

Reason for Failure Mode and Effect Analysis (FMEA) in Manufacturing Industries

While design or manufacturing a product, it’s better to identify the failures at the starting point of the process, or else the impact will show deadly results at the ending stage which leads to poor performance.

Below are some of the following examples:

  • Improves Design for Manufacturing and Assembly (DFMA)
  • It Open doors to solve many severe problems
  • Solutions for cost reduction
  • Continuous improvement, Process improvement is possible
  • Collaboration among product design and process.

When to Perform Failure Mode and Effects Analysis (FMEA) in Manufacturing Industries

  • When you want to develop a new product, service, or process
  • If you choose to perform the procedure in a different way
  • When you want to target a particular phase of change

In addition to that, an FMEA should occasionally be carried out throughout the process. On the other hand, for optimal results, quality and reliability have to be consistently checked and improved.

How to Execute Failure Mode and Effects Analysis (FMEA) in Production Industries

FMEA is carried out in seven steps and these steps are divided so that to ensure that each move is attended by exactly the right team members. Here is the sample example that how FMEA works in these seven steps

FunctionType of failureImpactSevereMajor causeOCCIdentifyRPN
Analyse the material in briefWhat leads to go wrongWhat is the major impact?How bad is it to the customerReason for the cause?How often is the occurrence?How easy is it to identifyRisk priority number
PVC profiles (Polyvinyl chloride) function: Specially used in doors and windows , durable materialLong and flat window profilesUnable to use the product as it doesn’t reach the exact requirements such as size, shape, colour and internal faults10Quality of the product and lack of mechanical properties of the material45200
Table 1: FMEA in doors and windows
Action NeededResponsibilityAction takenSevereOCCIdentifyRPN
What are the possibilities in reducing the causes?Who is responsible?What actions are taken into account?
Replacing the item and better to have extra profilesManufacturerReplacement of the item and carrying out additional profiles43560
Table 2:Actions performed

After a detailed analysis by the group of members, the team will be able to calculate the risk priority number (RPN) = Severity * Occurrence * Identify

Here is the step by step analysis of a product that is shown below to overcome the failures

FMEA Process Analysis Step by Step

Setting Preferences

Thus from the above table, it can be seen that once all failure modes have been identified, the team should modify the FMEA to mention the failures in the RPN descending order. There is no definite RPN threshold which areas should be the most carefully considered. It depends on a variety of factors, including market requirements, legal and security standards, and regulations. Likewise, the starting point for prioritization is the application of the Pareto rule typically, 80% of issues are caused by 20% of potential problems. As a rule of thumb, teams can initially focus their attention on failures with the top 20% of the highest RPN scores.

Making Corrective Actions

Once goals are decided, one of the last steps of the team is to establish adequate corrective measures to minimize or at least improve the frequency of fault modes. The FMEA leader should take over these steps and set target completion dates

After corrective steps have been taken, the team can meet again to evaluate and assess the severity, probability of identification of the top modes of failure. This would make it easier for them to measure the efficacy of corrective measures. These tests may be beneficial if the team determines that new disciplinary steps must be implemented in Product development

FMEA Relationship to Problem Solving

Failure modes in an FMEA are similar in problem solving to a problem statement or problem description. Causes in an FMEA are the same in problem solving as possible root causes.

  • In the verification of the root cause and continuous corrective action, design or process controls in an FMEA (PCA).
  • For future product planning or process consistency, data obtained from problem-solving shall be included in an FMEA. In order to make FMEA more efficient and complete, it should accept real failures, defined as failure modes and triggers.

Related keywords for manufacturing industries:

Analyze, Six Sigma, Design Process, Automotive, Root cause analysis, Process control, Cross-functional, Failure analysis, Mitigate, fabrication, Corrective action, Aerospace, Hazard

Methodologies, Prioritize, Severity, Problem-solving, Fault tree analysis, Reliability engineering, Worksheet, High risk, Defect. Lean Six Sigma, Handbook, Criticality, DFMEA, PFMEA, Risk analysis, Preventive

People also visited:

Mastering Job Interviews with AI and GPT-4: Tips and Techniques for Success
Comprehensive Guide to the German Job Seeker Visa: How to Apply, Eligibility, and Tips for Success
3D Printing Business Overview by Javaid Butt
Keeping Your Training Progress Private in European Workplaces
Cademix introduces a new career autopilot system for jobseekers, graduates and students
Business Consulting Response Times: Balancing Client Needs and Resources
Acuvue Oasys: The Ultimate Guide to Comfort and Clarity
Optimizing SEO for Multilingual Websites: A Comprehensive Guide
Optimizing Project Success: Strategies for Effectively Breaking Down Projects into Tasks
Optometrist Employment: A Guide for International Job Seekers
Skills for material engineers and industrial requirements
Speak Simply, Write Accurately: Interview Preparation Guide for Non-Native Speakers
Video CV: 2023 Strategic Approach to Stand Out in the Competitive Job Market
Autorefractor: Advancements and Applications in Optometry
Leveraging Technology in Modern Event Management
KI-gesteuerte prädiktive Wartung in Hochspannungsstromsystemen
SEO-Herausforderungen und -Strategien für mehrsprachige Websites
Role of Augmented Reality in the Future of Design
Pectin Extraction – A Review
Comprehensive Guide to the Best Resume Format: How to Choose and Use Them Effectively
The Impact of TinkerCAD and FreeCAD in the Industry
Comprehensive Guide to Curriculum Vitae Format Word: How to Create, Customize, and Use Professional ...
Sustainability in Event Planning: How to Go Green
Revolutionizing Manufacturing: The Future of Industrial Automation
Estimated Reading Time: 5 minutes

Must-Reads for Job Seekers

People also visited:

The Evolution of Color Lenses: A Journey Through History and Fashion
Keeping Your Training Progress Private in European Workplaces
Comprehensive Guide to Canva Resume Templates: How to Create and Use Them Effectively
The Science Behind Bifocal Contacts: An In-Depth Look at Optics and Vision Correction
Tailored Continuing Education: Challenges in Transitioning PhD Candidates to Sustainable Careers
Leveraging GPT and AI for Career Coaching and Professional Development
The Importance of Sustainable Business in Today's World
Career Development Stages
Indeed Optometrist: Finding Optometrist Jobs on Indeed
How GPT-4o Enhances Text, Voice, and Vision - GPT-4 Capabilities
Red Contact Lenses: Stylish Choices and Essential Safety Tips
Streamlining the Recruitment Process with Chat-GPT: A Guide for HR Professionals
AI Bias and Perception: The Hidden Challenges in Algorithmic Decision-Making
How can an Engineer become an Agile Project Manager?
Sustainable Practices in Farm Equipment for Sale: Embracing a Circular Economy
Global Impact of Plastics and Its Recycling
Optimierung der Effizienz in der Hochspannungsstromübertragung zur Integration erneuerbarer Energien
The Importance of Budget Management in Event Planning
Acuvue Oasys: The Ultimate Guide to Comfort and Clarity
How to Use Copernicus Satellite Data to Detect Incidents: 10 Step Tutorial
Success Story: Narendra Singh
Lower Tuition Fees for Low Income Countries
Innovating for a Sustainable, Eco-Friendly Design Revolution
Walk-In Eye Exams: What to Look for and Critical Considerations

Comments are closed.